B Flute Single Facer Corrugated Roller Mill Roll Stand 280mm

Single face mill stand Corrugated Machine Spare Parts

Electric Shaftless Mill Roll Stand

Electrical clamping, lifting & shifting, pneumatic braking, with expansion clip, electric appliances from Schneider
Technical Parameters:
1. Operation style of raw paper stand: electrically mechanical type
2. Range of clip paper(working width): 700 - 2000mm
3. Dia. of clip paper: Φ350mm - Φ1400mm
4. Max. weight of one side: 2000kg
5. Main stand shaft: Φ219mm
6. Total power: 5.2kw
Structural Features
1. The symmetric structure can be installed with two bundles of raw paper at the same time used to change papers without halt.
2. This machine adopts the electric driver to finish lifting up or down, clamping, loosening and centering the raw paper.
3. This machine adopts the pneumatic tension controller to adjust the tensile force of raw paper.
4. The head of clip paper adopts expansion style.
5. The tension control adopts pneumatic braking, which can also be on-line control together with Paper Splicer.
 

Main Bought-in Components and Raw Materials 
1. Main stand shaft: high quality thick wall seamless steel pipe, place of origin: Chengdu
2. Side wallboards: welded by high quality steel plates
3. Arms: casting HT200, place of origin: Hebei
4. Channels connected to main girder: 300mm, place of origin: Angang Steel Group
5. Electric motors: cycloid motor of arms 1/35: 0.75kw, 4 sets, intermittent working main shaft motor 1/59: 2.2kw, 1 set, intermittent working
6. Electric Appliances: Schneider
7. Pneumatic components: Taiwan Airtac
8. Bearings: produced in Harbin, Luoyang or Wafangdian.

Φ280mm Fingerless Type Single Facer

A B C E flute, fingerless type, Φ280mm corrugated roller made of high-quality alloy steel 48CrMo, chain transmission, electric appliances from CHINT
Technical Parameters
Working width: 900-2000mm
Working air pressure: 0.6-0.9MPa
Total power: 5.5kw

Structural Features
1. This machine adopts the wind adsorption to keep the stability of flutes.
2. The corrugated paper is adsorbed to the middle corrugated roller to form a negative pressure zone of 180°and then to finish the rolling of corrugation through the vacuum box by fan.
3. The width of suction slot of lower corrugated roller is not more than 2.6mm, able to reduce the stripe mark on single side corrugated cardboard.
4. The machine adopts chain transmission.
5. This machine adopts auto-cycle glue supply and pneumatic control glue supply and return, making it be characterized by buffering effect.
6. The glue roller surface is treated with special mesh nicking and chrome-plating.
7. The upper and lower corrugated rollers are made of 48CrMo high quality alloy steel. After heat-treatment, the hardness can be up to HRC58-62 The surface is grinded and chrome plated.
8. Flute profile: A B C E flute.
Parameters of Main Parts
1. Upper corrugated roller: Φ268mm Lower corrugated roller: Φ268mm
Pressure Roller: Φ268mm 45# seamless steel pipe, quenched
2. Glue Roller: Φ210mm 45# seamless steel pipe, surface treated with special mesh nicking and chrome-plating
3. Glue Scraping Roller: Φ120mm 20# seamless steel pipe
4. Pre-heating Roller: Φ268mm 20G Jigang steel
Raw Materials and Bought-in Components
1. Side Wallboards and base: casting HT200, place of origin: Hebei
2. Base of transmission parts: welded by channel
3. Electric Appliances: Schneider
4. Bearings: produced in Harbin, Luoyang or Wafangdian.

Sheet Cutter

Working width: 2000mm, electric appliances from CHINT
Technical Parameters
1. Working width: 2000mm
2. Cutting range: 390 - 2400mm
3. Cutting precision: ±3-5mm (at steady speed)